Thread Galling Issues with Stainless Steel Fasteners

Thread Galling Issues with Stainless Steel Fasteners

One of the benefits of working with stainless steel is its resistance to corrosion. Unfortunately, some people experience issues with stainless steel fasteners and wonder why their fasteners are breaking or getting nicks like cheap screws from the dollar store. Why isn’t this robust metal holding up?

It’s actually the fact that stainless steel is built to avoid corrosion that makes it more susceptible to thread galling. The varied grades of alloy create an oxidized surface to protect it from corrosion, but when pieces of stainless steel are compressed tightly together – especially if they’re the same grade – it is nearly impossible for the atoms to differentiate themselves from one piece of stainless steel to another, so they fuse and create some of these problems:

  • A bulge forms on one of the two surfaces due to the transfer of atoms. As the friction between the fasteners increases, this bulge grows and damages underlying metal.
  • Threads (either male or female) can tear away from their host piece of stainless steel, completely breaking the fastener or the tool responsible for turning it.
  • Molecular level-problems, which are not visible at all to the naked eye, can cause a bolt’s threads to seize or to twist off completely. Your supplier claims there’s nothing wrong with the product he’s selling you, but you continue to have these annoying instances where molecular-level problems quickly expand into something that can damage an entire machine.

Does any of this sound familiar?

Fortunately, there are ways to avoid stainless steel thread galling on your fasteners:

  • When you install the fasteners, slow down the RPM speed.
  • Coat individual pieces of stainless steel – especially their threads – with a lubricant and keep them well-lubricated as time and use wear on.
  • Use different alloy grades for the different pieces of each fastener. Because the materials will have a different hardness, they’ll be less likely to fuse with one another.

Below is a list of common causes of galling and prevention steps.

Chart

Share this Story
Load More Related Articles
Load More By Carlicia Layosa
Load More In Featured Articles

2 Comments


  1. Michał

    October 23, 2015 at 3:35 pm

    Therefore, stainless steel screws are becoming increasingly relevant. Especially when it comes to applying them to the natural atmospheric conditions where they are exposed to acid rain.
    http://www.e-nierdzewne.pl

    Reply

  2. Chris

    November 6, 2015 at 5:46 pm

    Make one of the mating parts out of an anti-gall stainless alloy, e.g. Nitronic 60. For instance if you need a tapped hole you can use a helicoil in that material, available off-the-shelf. Screws can be obtained in that material, though I haven’t seen them off-the-shelf yet. If you can use anti-seize compound, then by all means use normal stainless alloys. But many applications for stainless items prohibit lubricants. Hey Misumi.. how about adding anti-gall stainless steel screws to your catalog?

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

*

Check Also

4 Tips to Engineer Around the House

Whether working from home or needing to put ...

Get articles like this sent to your inbox every week:

Like us on Facebook

Follow us on Twitter @usa_misumi

Subscribe to our Channel

Follow @misumiusa on Instagram

  • MISUMI is on the move! We are excited to announce the relocation of our North American HQ to Glenstar’s Schaumburg Corporate Center. MISUMI is set to undergo a renovation of nearly 48,000 square feet spread over 2 floors of occupancy space. The relocation will allow a more expressive treatment of the MISUMI brand throughout the space. Read more, link in bio. #80Sextillion #ConfiguredToSaveTime
  • Wellness Fair at the office today. Thanks @chiroone @orangetheory  @weareonedigital #ConfiguredToBeHealthy #80sextillion
  • We crushed it at ATX West! Thanks to everyone who stopped by the MISUMI booth and crushed a can in the Bev-Bot 🔥. Let’s continue the conversation, find out how you can configure to save time. Link in bio. #atxwest #80sextillion #configuredtosavetime
  • MISUMI is excited to be at #slas2020 in San Diego. Are you attending? Stop by for a quick Rapid Design demo, and learn how you can save 30% design time! @slas_org #80sextillion
  • Head instructor John explains the different methods of proper installation for accuracy in linear guides during Master Class in Chicago. #80Sextillion #configuredtohavefun
  • Excited to be at #Engineer3D! in MKE. We started the day by kicking off the keynote presentation (swipe for the boomerang). We’re enjoying talking to and getting to know all the Engineers! Are you in attendance? Stop by the MISUMI booth to learn more about Rapid Design and get some swag #EnginerdOnBoard #gsc3d #80Sextillion #solidworks
  • We got spirit! Excited for football this Sunday 🏈 #configuredtohavefun #80Sextillion
  • Excited for the new graphics #Timelapse #ConfiguredToSaveTime #80Sextillion