# Understanding Gear Profile and Gear Module

The geometry of a simple spur gear tooth is complex. Numerous dimensional parameters define the shape of the tooth profile, determine how the gears fit together, and identify locations where forces act at the gear teeth.  Two of the most important parameters, often confused with each other, are the pitch diameter (or thread pitch diameter), typically denoted as (d) and the module (or modulus) usually denoted as (m).

The pitch diameter, in simplest terms, is a diameter of an invisible cylinder that would pass through approximately the “middle” of gear teeth, defining what’s commonly referred to as the “pitch circle”.  Furthermore, this pitch circle is defined as the circle centered at the gear axis that goes through the pitch point at the spur gear teeth.  This pitch point is located in between the root of the spur gear tooth, which denotes the minor diameter and the crest of the spur gear tooth, which denotes the major diameter of the spur gear tooth. This diameter is relatively easy to spot in a typical American Gear Manufacturer’s Association (AGMA) standard gear sizes, because it’s quoted as a diameter somewhere in between the minor and major diameters of the gear.

Without getting too detailed, the pitch diameter also defines the approximate mating envelope of two gears, meaning that the teeth will mesh along the pitch diameter.  In this way, it also defines an important concept called the line of action or pressure line.  This line defines the direction of the force acting on each tooth.   The pitch diameter also forms the basis on which the pressure angle of the tooth, the tooth thickness, and the helix angle of the gear are defined.

Unfortunately, pitch diameter cannot be measured directly on a physical gear.  Typically, an adequate approximation of the pitch diameter measurements can be obtained by measuring with calipers across two dowel pin placed in between the teeth of the gear at opposite locations on the gear.  Then, the diameter of one of the pins is subtracted from the measurement obtained by the calipers in order to arrive at an estimate of the pitch diameter.

This is part of the reason why the concept of the module (m) of the gear was introduced.  Quite simply, it’s the ratio of the pitch diameter (d) to the number of teeth (N) on the gear:

The module is typically quoted in standardized gear sizing charts with implied units of length, either (mm) for SI units or (in) for BG units.  In a sense, it’s a measure of the unit size of the gear on the basis of the number of teeth present on the gear.  A useful analogy is that the module defines the “size” of each tooth as a portion of the pitch diameter “pie.”  This really means that each tooth possesses a “module” unit of the portion of the total pitch diameter.   For example, a gear that possesses a module of 10 (quoted in SI units) quite literally means that that each tooth “uses” 10 (mm) of the total pitch diameter.

In this way, the module is a very easy parameter to use to determine if two gears of differing pitch diameters will be able to mate together; two gears with different modules will not mate together because the unit size of the gear, as discussed above, must match in order for gears to mate together,

Finally, given only the gear module, a number of other geometric gear parameters can be calculated, such as diametric pitch and circular pitch.   Both gear pitch diameter and gear module are two related yet distinct parameters that are very useful to know for gear selection and sizing, as international gear standards and general design disciplines now rely heavily on the use of these parameters.

Share this Story
• ### Understanding Gear Profile and Gear Module

The geometry of a simple spur gear tooth is complex. Numerous dimensional parameters define the shape of the tooth profile, determine ...
• ### Video: IN Motion – Offset Conveyor Station

One of the biggest concerns in assembly factories is the production line footprint, or the area that automation stations occupy. In ...
• ### Q&A: Center to Center Spacing for Shafts with Spur Gears

Question: Dear MISUMI Engineering Team: We are currently building a machine that has several timing shafts that are driven by spur ...
• ### Gears Part 2: 5 Common Gear Types

In the introduction to our gears series we wrote about Backlash and Gear Ratios. Now that you have more background information ...
Load More Related Articles
• ### A Peek Into MISUMI’s New Home

MISUMI headquarters has relocated to a state-of-the-art building in Schaumburg’s beautiful Corporate Center. We thought we’d share a snippet of what ...
• ### How To Measure Fitting Threads in 3 Steps

MISUMI fluid power partner and expert Brennan Industries is back with some tips on how to measure fitting threads. The precise ...
• ### 5 Things You Should Know about O-ring Face Seal Fittings

Guest brand Brennan is back for another informative post about O-ring Face Seal Fittings (ORFS). They are a highly popular and ...
• ### NAAMS Locating Pins Hardness Testing Comparison

Material surfaces can wear over time due to the application environment. To combat this, heat treatment is often specified to increase ...
• ### Design Application Examples Using Linear Shafts

Whether you’re building a new machine or considering making modifications on an existing machine, engineering effort, cost and time are all ...
• ### The Anatomy of a Micrometer and How to Read Them

A micrometer is one of the instruments used to measure objects of various small sizes. In this post, we will review ...
Load More By Carlicia Layosa
• ### How To Measure Fitting Threads in 3 Steps

MISUMI fluid power partner and expert Brennan Industries is back with some tips on how to measure fitting threads. The precise ...
• ### [Case Study] Sourcing Custom Cable Harnesses

Background An automotive company urgently needed over 80,000 custom cable harnesses for a project.  Prototypes had yet to be built for ...
• ### 5 Things You Should Know about O-ring Face Seal Fittings

Guest brand Brennan is back for another informative post about O-ring Face Seal Fittings (ORFS). They are a highly popular and ...
• ### Design Application Examples Using Linear Shafts

Whether you’re building a new machine or considering making modifications on an existing machine, engineering effort, cost and time are all ...
• ### The Anatomy of a Micrometer and How to Read Them

A micrometer is one of the instruments used to measure objects of various small sizes. In this post, we will review ...
• ### Introduction to Fittings: Connection Types

What fitting do you need? There are a variety of standards available to select from. We worked with our partner and ...
Load More In Tips & Tricks

1. ### Suresh

March 25, 2018 at 2:47 am

Bearing catalog send

2. ### Chris Pederson

December 2, 2020 at 10:03 am

I am recently getting into machining and gears. I was told that I should know as much about spur gears as possible. You said they are complex and the dimensional paramreters seemed a bit confusing so I’ll keep looking for more information. Thank you for sharing what you know!

## A Peek Into MISUMI’s New Home

MISUMI headquarters has relocated to a state-of-the-art building ...